[1]李宣默,张亚婷,谢聿铭,等.镁合金连续送丝搅拌摩擦增材制造技术研究[J].中国材料进展,2026,45(12):060-69.
LI Xuanmo,ZHANG Yating,XIE Yuming,et al.Wire-Based Friction Stir Additive Manufacturing of Magnesium Alloy[J].MATERIALS CHINA,2026,45(12):060-69.
点击复制
镁合金连续送丝搅拌摩擦增材制造技术研究()
中国材料进展[ISSN:1674-3962/CN:61-1473/TG]
- 卷:
-
45
- 期数:
-
2026年12
- 页码:
-
060-69
- 栏目:
-
- 出版日期:
-
2026-11-30
文章信息/Info
- Title:
-
Wire-Based Friction Stir Additive Manufacturing of Magnesium Alloy
- 作者:
-
李宣默; 张亚婷; 谢聿铭; 孙秀文; 等。
-
1. 材料结构精密焊接与连接全国重点实验室,哈尔滨工业大学,黑龙江 哈尔滨 150001
2. 北京新风航天装备有限公司,北京 100000
- Author(s):
-
LI Xuanmo; ZHANG Yating; XIE Yuming; SUN Xiuwen; et al.
-
1. State Key Laboratory of Precision Welding & Joining of Materials and Structures, Harbin Institute of Technology, Harbin 150001, China
2. Beijing Innowind Aerospace Equipment Co., Ltd, Beijing 100000,Chin
-
- 关键词:
-
搅拌摩擦增材制造; 镁合金; 旋转速率; 微观组织; 力学性能
- Keywords:
-
friction stir additive manufacturing; magnesium alloys; rotational velocity; microstructure; mechanical properties
- 文献标志码:
-
A
- 摘要:
-
镁合金传统熔化增材制造易受氧化、元素挥发及气孔、裂纹等缺陷制约,连续送丝搅拌摩擦增材制造通过固相成形为避免上述缺陷提供了可行方案。本文采用该方法实现了 AZ31B镁合金的固相增材成形,并研究了旋转速率对成形特征、微观组织及力学性能的影响。结果表明:旋转速率由 350 rpm提高至 400 rpm时,增材工具稳定阶段峰值温度由 507.5 ℃升高至 521.8 ℃,材料塑化和流动状态得到了改善,350 rpm条件下出现的局部层间成形缺陷在400和 450 rpm条件下得到了抑制,试件实现了稳定连续沉积。350、400和 450 rpm条件下试件均形成了细小等轴晶和强基面织构,平均晶粒尺寸分别为8.46 ± 5.08、9.95 ± 6.23和 8.46 ± 4.93 μm。试件行进方向和增材方向的最高抗拉强度分别达到了 257 ± 2和 243 ± 6 MPa,对应断后伸长率分别为 7.8 ± 0.5%和 8.7 ± 0.5%;各试件断口均观察到了韧窝特征,总体以韧性断裂为主。连续送丝搅拌摩擦增材制造兼具低缺陷、连续成形和较高力学性能等特点,为镁合金高性能固相增材制造提供了新的技术途径。
- Abstract:
-
Conventional fusion-based additive manufacturing of magnesium alloys is constrained by oxidation, elemental evaporation, porosity, and cracking,whereas wire-based friction stir additive manufacturing (W-FSAM) provides a solid-state route to avoid these defects. W-FSAM was employed to fabricate AZ31B magnesium alloy, and the effects of rotational velocity on forming characteristics, microstructure, and mechanical properties were investigated. The results showed that increasing the rotational velocity from 350 to 400 rpm raised the steady-state peak tool temperature from 507.5 to 521.8 °C, improved material plasticization and flow, and suppressed the local interlayer defects observed at 350 rpm, enabling stable continuous deposition at 400 and 450 rpm. Fine equiaxed grains with a strong basal texture were formed at 350, 400, and 450 rpm, with average grain sizes of 8.46 ± 5.08,9.95 ± 6.23, and 8.46 ± 4.93 μm, respectively. The highest ultimate tensile strengths along the traveling and building directions reached 257 ± 2 and 243 ± 6 MPa, respectively, with corresponding elongations of 7.8 ± 0.5% and 8.7 ± 0.5%. Dimples were observed on the fracture surfaces of all specimens,indicating predominantly ductile fracture. W-FSAM combines low-defect forming, continuous deposition, and high mechanical properties,showing potential for high-performance solid-state additive manufacturing of magnesium alloys.
更新日期/Last Update:
2026-11-02